| From | Message |
slider_buck
Dodge Dakota
JOIN HERE
1/20/2002
02:01:57
|
 Subject: ? for bernd- m1 intake
IP: Logged
Message:
i just ordered an m1 2bbl intake. do you have any suggestions or tips on installing it? what kind of performance can i expect from it? thanks in advance for the info
|
slider_buck
Dodge Dakota
JOIN HERE
1/20/2002
02:02:55
| RE: ? for bernd- m1 intake
IP: Logged
Message:
by the way its a 99 r/t
|
bernd
*GenIII*
 
1/20/2002
10:05:02
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Make sure you get the installation kit, gaskets, and some extra vacuum hose for the brake booster.
Tips: Drain the coolant about 1 gallon, change the oil after you're done (before starting it up), use "The Right Stuff" on both front and rear seals (allow to tack up a bit before putting the manifold back down), let the PCM "learn" the new manifold for about 50 miles. Then...floor it and hang on. :)
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
Anthony G
Dodge Dakota
JOIN HERE
1/20/2002
18:22:16
|  RE: ? for bernd- m1 intake
IP: Logged
Message:
Bernd,
"use "The Right Stuff" on both front and rear seals (allow to tack up a bit before putting the manifold back down)"
Does the Mopar gaskets kit not have a gasket for that section? Is silcone required to complete the M1 install?
"let the PCM "learn" the new manifold for about 50 miles. Then...floor it and hang on. :)"
What if I can't wait 50mile until I Floor it? How long should I wait until I can run the engine if silcone is used to seal up the front and back areas?
|
slider_buck
Dodge Dakota
JOIN HERE
1/20/2002
18:27:18
| RE: ? for bernd- m1 intake
IP: Logged
Message:
i got the installation kit with it from mancini racing. will the gasket come with the manifold or installation kit or will i have to purchase it seperately?
|
Anthony G
Dodge Dakota
JOIN HERE
1/20/2002
19:45:06
| RE: ? for bernd- m1 intake
IP: Logged
Message:
If they didn't mention it, I doubt it.
I already have my Install Kit and should have my M1 and gaskets this Tuesday.
|
kota on 20s
GenIII
1/22/2002
23:04:33
| RE: ? for bernd- m1 intake
IP: Logged
Message:
where did you order it from? and how much?
Eric
|
bernd
*GenIII*
1/22/2002
23:43:41
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Just in case...I can get the M1 2BBL-MPI Manifold (with Installation kit and gaskets) for $375 shipped.
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
kota on 20s
GenIII
1/22/2002
23:50:47
| RE: ? for bernd- m1 intake
IP: Logged
Message:
i want one! how long do i have to wait?
Eric
|
Josh Lee
Dodge Dakota
JOIN HERE
1/23/2002
07:28:26
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Bernd, I have read conflicting stories about the M1 manifold. Do they hurt bottom end torque in favor of top end HP or is it strictly a stock replacement that enhances power throughout the range? Just wanting to clarify if I want one or not...
Also, is it $375 shipped from you or another place? (stupid question probably)
Thanx.
|
McClane
Dodge Dakota
JOIN HERE
1/23/2002
10:31:38
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Bernd
A while back, you mentioned that the M1 was on back order. Do you know if DC has gotten around to filling out the huge number of back orders ?
Last I checked with the dealer, there was 95 back orders for the M1.
|
Brian Gaarder
Dodge Dakota
JOIN HERE
1/23/2002
20:36:46
| RE: ? for bernd- m1 intake
IP: Logged
Message:
I have a friend that works fot the parts dept. ata dodge dealer..... he told me that they are on a massive backorder..... and wont be shipping for a long time....
|
YA
Dodge Dakota
JOIN HERE
1/23/2002
21:13:29
| RE: ? for bernd- m1 intake
IP: Logged
Message:
UPS droped mine off today. Got it from Mancini Racing.
|
slider_buck
Dodge Dakota
JOIN HERE
1/23/2002
21:38:22
| RE: ? for bernd- m1 intake
IP: Logged
Message:
got mine today also. can't wait to get it on. hey ya let me know of any problems you run into if you will. i probably won't get mine on till sunday sometime.
|
YA
Dodge Dakota
JOIN HERE
1/23/2002
23:27:19
| RE: ? for bernd- m1 intake
IP: Logged
Message:
I think I'm going to use my die grinder on it in a few places that need cleaned up.
Next week befor i get mine on. I can't see where there will be any problems on the install.
Gonna try mine with 24# injectors.
|
bernd
*GenIII*
1/25/2002
10:22:15
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Myself and WorldWide Performance Parts have them for $375 shipped (limited quantity in stock).
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
bernd
*GenIII*
1/25/2002
10:22:50
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Oops...forgot to add:
The $375 includes the Installation Kit and Manifold gaskets.
1997 Dodge Dakota SLT - V6
Supercharged/Intercooled @ 10# w/Nitrous
14.55 @ 96.01mph
|
slider_buck
Dodge Dakota
JOIN HERE
1/28/2002
20:07:15
| RE: ? for bernd- m1 intake
IP: Logged
Message:
hey folks got my m1 installed. between it and the mopar computer my g-tech showed me an increase of 22 h.p. and .3 off of my 1/4 mile. i figured i would get 22 h.p alone out of the intake. could be my g-tech screwing me also, i think that thing is not very good for figuring out h.p. it relies on too much stuff to be just right, especially the weight you enter. ohh well. the installation was a breeze, took me about 5 hours. all and all i would say that i'm pleased with it.
|
NeedForSpeed
Dodge Dakota
JOIN HERE
1/28/2002
23:35:30
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Does it pull hard all the way to the rev limiter or does it run outta breath like the beer keg?
|
slider_buck
Dodge Dakota
JOIN HERE
1/29/2002
01:20:39
| RE: ? for bernd- m1 intake
IP: Logged
Message:
i had the mopar computer on with the stock intake and it felt like it was falling on its face badly when it would rev up with stock intake but with the m1 it pulls hard all the way till it shifts. i did notice a loss in bottom end though, which is good for me though. before i would spin the tires till around 35mph if i mashed it from a dead stop. it will still break them loose from a dead stop with the m1 but not as bad as before.
|
NeedForSpeed
Dodge Dakota
JOIN HERE
1/29/2002
01:48:05
| RE: ? for bernd- m1 intake
IP: Logged
Message:
Theres a dude that put his on and said it lost the bottom end at first but once the PCM learned the new intake was on he gained it back. Did U put the 2bbl or the 4bbl on?
|
slider_buck
Dodge Dakota
JOIN HERE
1/29/2002
03:16:01
| RE: ? for bernd- m1 intake
IP: Logged
Message:
i put the 2bbl on it. i have driven it long enough for the computer to learn about it but it still doesn't feel like it did before. i love it anyways though because once it does start to pull strong it really pulls clear up till it shifts.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
