From | Message |
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/11/2003 16:24:14
|
Subject: 4.7L Poweraid TB Spacer IP: Logged
Message: Anyone have a 4.7 with a throttle body spacer on it? I have a Poweraid TB Spacer on order and should be here in a week or so. Just wondering if anyone has any history with one that you could share. Increase in mpg? power? response? I'll let you know how mine makes out when I get it>!
|
Jimi Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/11/2003 19:00:31
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: There is no dyno spec sheet to show they do anything (4.7) if they did there would be a page in here, these work with carburators to help even out and better mix the fuel/air intake, being the 4.7 is injected directly in the cylinder there is no mixing nessesary.Air only! If you can return it, you could have the money better spent elsewhere, they sell them for the 4.7 because they can,,thats biz!
|
kevster Dodge Dakota JOIN HERE
1/11/2003 20:14:24
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Cory, send it back, dont open pkg just refuse shipment and have it sent back, this will save you from paying shipping cost again, when they get it back they will refund you, make sure you call them and let them know.. The spacer does ZIP for any engine. waste O money. buy a Airaid cold air intake for 160.00 this works. along with the Jet module stage II Not a stage I,is weak.
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/12/2003 12:11:28
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Wish I knew that a week ago. Thanks!
|
Ed Halterman Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/12/2003 22:28:18
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Have any of you actually run one on the 4.7?? I have. And it's still on there for a reason. It works, plain and simple. It does not work on the 3.9/5.2/5.9 motors due to the different intake design. It is most noticeable in part throttle acceleration, like around town, and yes, my mpg did go up a bit. Is it worth the $90?? Imo, yes. You won't feel it during wide open throttle, but you will cruising around town.
|
Ole GenIII
![User Profile](http://www.dodgedakota.net/amb/icons/profile.gif)
![](http://www.dodgedakota.net/members/profiles/1072
/thumbnail.gif)
1/13/2003 00:17:28
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Ed, dyno it . . .
(then I'll buy one . . . if it works)
Go Fast -Take No Chances !
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/13/2003 07:23:32
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Well, for $52 I figured i'd take the chance. What the hell.
|
Texas Todd Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/13/2003 09:17:40
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Cory,
If you're isterested on any mods for your ride, do a search here on this site first, then just ask, 2nd, get many opinions, facts, etc. and then make your choices.
Got HO?
|
Ed Halterman Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/13/2003 23:13:15
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: It won't show gains on the dyno, like I said earlier, you feel it during part throttle cruising, like driving around town, not during WOT.I was even told that. I spend more time around town than on the strip, so WOT doesen't mean as much to me (well, it does, but you know :) )I was having a weird prob with the truck last year, so I took it off when it went to the dealer, and you know what? My throttle response wasn't as great, and I had to step down on the go pedal a little more than usual. All I say is this. I only put things on that work. I've been around motors all my life. Try it. If you don't like it, you can always return it and get your money back. BUT, I betchya lunch that you'll like it.......... The only thing that annoys most people about it is that it has a slight whistling sound when you get on it a little bit. Doesen't bother me a bit, kinda sounds like a mini s/c or turbo.
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/14/2003 07:04:00
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Well if I can hear that over the intake or the new 32 A/T's then it must be loud! Oh by the way, I received the TB Spacer yesterday and am planning on doing the install tonight or tomorrow night (probably tonight b/c I can't wait to try it out)
|
Jimi Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/14/2003 07:25:16
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Good luck Cory, keep us posted on your findings, I am not sure I trust Ed "I work the Poweraid booth at the Vegas Auto Show" Haltermans sales pitch! HA! Just kiddin Ed!
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/15/2003 11:35:29
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: UM HELP! OK, I went to install the TB spacer and found that my throttle and cruise cable are too short, they hold the throttle open aby about 1/2". How do I extend the cables or modify the bracket? Do they sell a mod bracket? Ed how did you do yours?
|
2THEXTRM GenIII
![User Profile](http://www.dodgedakota.net/amb/icons/profile.gif)
![](http://www.dodgedakota.net/members/profiles/1110
/thumbnail.gif)
1/15/2003 11:49:36
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Cory, your kit should have came with 5-6 aluminum extensions and screws that move the throttle bracketry forward the same distance as TB spacer thickness. If you are not using the factory airhat, you will have a couple left as they help relocate that foward also. Good-luck!
Flowmaster cat back w/15 inch chrome tip, Volant Intake, Poweraid TB Spacer, Splitfire Plugs, full synthetic fluids 3 inch body/1.5 inch Block Lift, 305 70-16 X-Terrains on AR Terons, Pro Comp ES9000's Grizzly double/single rollbar with (6) Hella's, Manik Nerfs, Line-X, Hard Work & $$$$$$$$$$
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/16/2003 13:08:20
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: OK, it's installed. The part came with the necessay spacers, and with some slight bending of the throttle cable bracket it went in very smooth. So far the the results have been a definite increase in throttle response while at cruising speeds. between 2500-3500 rpm it has GREAT response. The only noise is a slight whistle when the throttle is just cracked open. full close or open more and no noise what so ever. For $57 I am very pleased!!!
|
Ian Dodge Dakota JOIN HERE
1/16/2003 13:21:50
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: What ever happened to that guy selling the "Motorvator" tb spacer, he said he would come back to the forum with some dyno #'s after the holidays?
|
Ed Halterman Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/17/2003 00:22:29
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Told ya so. Too bad though, you won't be able to try my killer chili recipe........
|
Duncan Patter Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/21/2003 00:04:06
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Hi Cory, I have been planning on purchasing the Poweraid TB spacer. Where did you find yours for $52.00? That is a great price.
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/21/2003 07:26:25
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Duncan, I actually got it through an Ebay auction from an off-road accessories warehouse in Minnesota. Here is the URL for the company
www.burnsvilleoffroad.com
The price on the box from them was tagged $119.99, so $57.00 I got a great deal.
|
sean Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/22/2003 09:57:46
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: Hey cory, glad it worked out for ya, my suggestions for your next moves are a Volant cold air intake and a stage II jet chip, i made these additions to my 4.7, and it took me from mid 15's to mid to high 14's in the quarter.
good luck
|
Cory Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
1/22/2003 10:12:39
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: I already have a cold air intake made by 360 intakez, and the stage II jet chip will have to wait until i get my dual exhaust on, since the real benefit won't be seen until that is on. You can't take in more air than you can exhaust, so my 4.7 still isn't ready to breathe easy!
|
Demon Dakota DakotaEnthusiast
![User Profile](http://www.dodgedakota.net/amb/icons/profile.gif)
![](http://www.dodgedakota.net/members/profiles/1245
/thumbnail.gif)
1/22/2003 11:45:46
| RE: 4.7L Poweraid TB Spacer IP: Logged
Message: TB spacer doesn't do anything, but it makes a nifty whistling noise. What kind of exhaust are you going to have Cory? If you can find a shop that does good quality work, go with true duals (2.25"-2.5" maximum diameter piping). If your state/county has strict emmisions laws, buy two high flowing cats and then whatever mufflers you want to run. I just run the mufflers and not the high flow cats on my truck (relatively lax emmisions in Gwinnett Co, GA). Definitely provided me with some good HP gains (along with my other mods).
K&N Drop in AF True Dual exhaust and removed third cat HO Cams & HO Intake Modified TB Autolite 3923 Plugs TPS @ .76 VDC IAT Adjuster Mod 14.52@94.2 MPH at Silver Dollar Raceway
|
| P 1 |
|
Post a reply to this message:
Username Registration: Optional All visitors are allowed to post messages
|