| From | Message |
killerdakota@
Dodge Dakota
JOIN HERE
2/22/2004
08:46:37
|
 Subject: cams
IP: Logged
Message:
i have a chance to get a cam for my 99 3.9 dak i got a cold air intake and the chip free flowing exhaust etc on and on heres the discription for it will it work ?
This cam makes an excellent HP/TQ curve (20-25 RWHP above stock) and would work with superchargers / turbochargers. SPECS: ----Part # REGRTND03515 Hydralic Roller Special-- ---- Grind # HR-20B/292-2S-14-- ----.467"/.520" lift. ---with 1.6 ratio rockers.-- ---- 208/214 Duration-- ---- Most boost in power from 1500-4500 rpm
|
J and J Auto
GenII
2/22/2004
14:09:13
| RE: cams
IP: Logged
Message:
Yes it will work but you will also need to upgrade
the valve springs because the stock springs will
bind over .500 lift
R/T springs retainers and keepers
P4529218 keepers $9.95
P5249464 springs .400 to .525 lift $84
P4452032 retainers $60
Availible at any chrysler dealer or online at
http://www.mopartsracing.com/parts/ram.html
Larry
J&J Auto
|
killerdakota@
Dodge Dakota
JOIN HERE
2/26/2004
21:18:18
| RE: cams
IP: Logged
Message:
will i need longer pushrods ?
|
J and J Auto
GenII
2/27/2004
14:50:40
| RE: cams
IP: Logged
Message:
You will only need longer push rods if its a
regrind and the base circle on the cam was
made smaller
Or just go with the crower 1.6 adjustible roller rockers
Larry
J&J Auto
|
killerdakota@
Dodge Dakota
JOIN HERE
2/27/2004
17:12:09
| RE: cams
IP: Logged
Message:
will there be any other problems?
|
J and J Auto
GenII
2/27/2004
17:36:53
| RE: cams
IP: Logged
Message:
No other probs but that is a regrind from looking
at the part # Part # REGRTND03515
longer push rods or adjustible rockers needed with
that cam
Larry
J&J Auto
|
killerdakota@
Dodge Dakota
JOIN HERE
2/27/2004
17:42:40
| RE: cams
IP: Logged
Message:
how could i get push rods ?
|
J and J Auto
GenII
2/27/2004
19:20:14
| RE: cams
IP: Logged
Message:
contact the company and see if the base circle on
the cam was altered first.
They make adjustible and also longer push rods
call crower they will be able to help you out if
you need them
Hughes also may carrie them
Larry
J&J Auto
|
killerdakota@
Dodge Dakota
JOIN HERE
2/27/2004
19:45:51
| RE: cams
IP: Logged
Message:
thanks larry
your a great help
|
rtdkota
R/T
2/29/2004
01:43:38
| RE: cams
IP: Logged
Message:
that cam is going to give you fits in the chk eng dept... you need to run longer pushrods as it lists a regrind-- which WILL be a smaller base circle than stock. You'll have to measure the pushrod length with an adjustable checking pushrod. I sell 'em for $20 + shipping. Based on your measurements, I can get you the correct length pushrods custom made by Crower.
(and of course the rockers too ;)
Sam
619-274-1292
www.socaldakota.com
|
killerdakota@
Dodge Dakota
JOIN HERE
2/29/2004
10:17:10
| RE: cams
IP: Logged
Message:
i think its way to involved to do in a drive way if some one makes me a decent offer it theres
|
killerdakota@
Dodge Dakota
JOIN HERE
2/29/2004
10:23:48
| RE: cams
IP: Logged
Message:
also it comes with 12 mopar performance valve springs
|
Greg
Dodge Dakota
JOIN HERE
2/29/2004
16:26:23
| RE: cams
IP: Logged
Message:
It's not really all that bad to do as long as you mark and keep up with everything... I think it took me around 3 or 4 hrs to pull everything apart, still waiting to order everything and put it back together though :// You will however need somewhere dry atleast to do the work and some minor speciality tools...
|
killerdakota@
Dodge Dakota
JOIN HERE
2/29/2004
20:59:58
| RE: cams
IP: Logged
Message:
ill take the best offer email me at killerdakota@comcast.net
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
