Forums
Forum Tools
|
 |
23:08:49 - 12/19/2024
V6 Dakotas
| From | Message |
Adam
Dodge Dakota
JOIN HERE
1/17/2004
13:32:14
|
 Subject: grinding noise
IP: Logged
Message:
I have a 98 3.9 and when i take it around left hand turns it makes a whining noise and grinding noise but as soon as i turn right it stops. I was wondering if anybody knew what might be making it do that? thanks
|
brianl
GenIII
1/17/2004
18:39:43
|  RE: grinding noise
IP: Logged
Message:
90% chance it is a bad ball joint, but could be a wheel bearing also. How many miles are on your truck? Have you had the ball joints replaced yet? I've replaced all of my ball joints with Moog greasable joints. If you need part numbers let me know.
Brian
Dynomax UltraFlo, V8 TB, Alpine 6-disc, 180 T-Stat, PA 3" Lift, Prothane bushings, Autolite 3923, homemade intake, Rancho RS9000, Tonneau, Herculiner Sprayed-In, 33" Dueler A/T, AR Baja 16x8 Wheels, MOOG Balljoints and Ties, Powerslots w/ Raybestos PG pads
|
Adam
Dodge Dakota
JOIN HERE
1/17/2004
19:34:17
| RE: grinding noise
IP: Logged
Message:
My truck has a little over 50,000 miles on it... if you would could you give the the part #s for those bearing and ball joints just incase
|
brianl
GenIII
1/17/2004
20:37:01
| RE: grinding noise
IP: Logged
Message:
The numbers are MOOG Part#K7242 for uppers and MOOG Part#7267 for lowers. Unfortunately you cannot just replace the wheel bearings. You have to replace the entire hub assembly. Autozone carries those. Part numbers depend on whether or not you have ABS. More than likely it is the ball joint though. If you plan on changing them yourself, you'll need to grind off the rivets on the existing upper control arm bracket. The new upper comes with bolts to use instead of rivets. The lower one is a real pain and requires a torch to heat up the exisiting ball joint and smack it out. You'll need to heat up the new joint as well to "slide" it in. Hope this helps.
Brian
Dynomax UltraFlo, V8 TB, Alpine 6-disc, 180 T-Stat, PA 3" Lift, Prothane bushings, Autolite 3923, homemade intake, Rancho RS9000, Tonneau, Herculiner Sprayed-In, 33" Dueler A/T, AR Baja 16x8 Wheels, MOOG Balljoints and Ties, Powerslots w/ Raybestos PG pads
|
Paul
Dodge Dakota
JOIN HERE
1/23/2004
01:03:52
|  RE: grinding noise
IP: Logged
Message:
I just had a similiar problem the problem was grumbling above 20mph, but it was carrier bearings. Had the open rear end removed and replaced with Dana posi, new 3.55's and all new bearings including wheel bearings. My guess is it's the wheel bearings. Those can make that whining on left and right hand turns
|
TGI
Dodge Dakota
JOIN HERE
1/23/2004
11:55:51
| RE: grinding noise
IP: Logged
Message:
I have a 99 dakota is the grinding in the steering or in the drive train... Next question... do you have a limited slip diff.. if you do it might be that. mine sounded like the rear was going to explode. i took it apart to replace a wheel seal and found some of the limited slip clutchs are broke now it makes a poping noise. but if its just grinding a little i wouldnt worry about it, just turn the radio up
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
|
