| From | Message |
slow97dakota
Dodge Dakota
JOIN HERE
10/03/2003
20:02:24
|
 Subject: whos got a msd?
IP: Logged
Message:
i just bought a 6a off a friend for 70 dollers never used! my question is what else do you need other then the 6a i know i have herd some poeple on this fourm talk about needing another part for this so it doesent throw a code? also does any one use the msd coil along with it? if so whats the part # for it?
|
tazzy
GenIII
10/03/2003
20:07:56
| RE: whos got a msd?
IP: Logged
Message:
8910 tach adapter..for no codes..
I use the 8998 coil..but I hear a lot use the BlasterSS coil..
Brass Cap& Rotor
K&N Drop in
Relocated IAT
MSD6a
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
slow97dakota
Dodge Dakota
JOIN HERE
10/03/2003
20:54:31
| RE: whos got a msd?
IP: Logged
Message:
thanks for the help man. also are resistor core sprak plug wires alright to run with the 6a? i know your not sopost to run solid core, but are resistor core wires fine?
|
TuckerLudlow
Dodge Dakota
JOIN HERE
10/04/2003
14:09:27
| RE: whos got a msd?
IP: Logged
Message:
Boy, you got a deal on that that MSD-6A. I've been trying to snag one on eBay, and haven't won an auction yet!
MSD folks told me to get the MSD-8207 coil and a set of their universal wires (p/n 32969, I think) - you have to cut them and put the ends on yourself. I almost bought a set of Mopar Performance wires, but then learned that they were only 7.5mm wires. Also, this stuff should be mounted AWAY from the pcm.
He claimed that you don't need anything special for the cap and rotor, but I'd go with what you've seen here where people get the brass stuff from NAPA.
|
PAD
Dodge Dakota
JOIN HERE
10/04/2003
21:36:38
|  RE: whos got a msd?
IP: Logged
Message:
I have a Jacobs Pro Street set-up on my '94
Dakota and have had no problems with it. It
is a multiple spark discharge type of ignition
with an adjustable rev limiter, anti-theft,
and a few other features. There was a notice-
able improvement in power with it.
|
Kirk Hines
Dodge Dakota
JOIN HERE
10/05/2003
07:30:19
| RE: whos got a msd?
IP: Logged
Message:
Im running the MSD6A with MSD 8.5 wires, the only problem with the wires is the tight fit on the distributor caps since the terminal boots are so large. Also I have to change my Borg Warner cap every 5-7000 miles as the MSD really fowls it up with the extra voltage.
|
J and J Auto
GenII
10/06/2003
15:16:24
| RE: whos got a msd?
IP: Logged
Message:
You can run the stock wires with the Box but
if you upgrade the coil you will need better wires
Just get the MDS 8.5 super conductor wires for the
V8 and they will fit perfict you just have 2 wires
left over and no screwing around with the ends.
about $60
Napa MO26 MO28 brass incerts cap and rotor made
by Borge Warnner and sold under the Echlin name
Larry
J&J Auto
|
TimG
Dodge Dakota
JOIN HERE
10/06/2003
15:44:23
| RE: whos got a msd?
IP: Logged
Message:
I just ordered a set of MSD wires, 8998 coil and the tach adapter. I'm sure there's directions, but where does the tach adapter go ??
|
tazzy
GenIII
10/06/2003
15:59:31
| RE: whos got a msd?
IP: Logged
Message:
The tach adapter will have install intructions with it..
Easy to do..
Brass Cap& Rotor
K&N Drop in
Relocated IAT
MSD6a
Bullet Muffler
TPS mod
"S"bolt
180Tstat
Trans cooler
|
massivdak
Dodge Dakota
JOIN HERE
10/06/2003
16:52:30
| RE: whos got a msd?
IP: Logged
Message:
what is thepricetag on the brass cap and rotor and who diffucult is the install
|
J and J Auto
GenII
10/07/2003
21:18:29
| RE: whos got a msd?
IP: Logged
Message:
The cap and rotor is around $15 at Napa.
2 screws to remove the cap just locate the #1 and
change the wires 1 at a time in the right order
if you do pull them all off the order is clockwise
165432
6 5
4 3
2 1
FAN
the rotor just pull up and off, and line up the
new one and push down on they only go 1 way you
will see a little tab to line up
Larry
J&J Auto
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
