| From | Message |
mikes00dakota
Dodge Dakota
JOIN HERE
7/23/2003
23:16:13
|
 Subject: mods
IP: Logged
Message:
i need some advice. i have a 2000 w/auto 3.9. i am going to put on an intake, custom exhaust, chip,tb, crankcase breather, headers, autolite
3923's, wires, electric fan, and 180 thrmo. i need to know what the best brands are where i can get them( preferbly cheap, $ is tight).
thanx-mike
ps: whats an IAC. i've seen that ppl have relocated as a mod.
|
F585
Dodge Dakota
JOIN HERE
7/24/2003
04:45:30
|  RE: mods
IP: Logged
Message:
IAC it is isntalled in pass side of intake, right behind the alt. Pull it out, install a 1/4npt pipe plug with high temp silicone on threads in that hole. Then take, install IAC in your air intake tubing but after your air filter. You will need to extend and SOLDER wires to it. Good cheap mod.
Richard
|
digital
Dodge Dakota
JOIN HERE
7/24/2003
05:17:33
| RE: mods
IP: Logged
Message:
that's the IAT not IAC, big difference ppl. You would really jack the engine up on top of it wouldn't run properly if you move the Idle Air Controller (IAC). ppl here move the Intake Air Temperature (IAT) sensor.
go get a 1/4 NPT pipe plug, thread it and put the plug about midpoint between the airhat and filter, DONT cut the wires, just move it till it's fully extended. that's how I did it, along with the other hundreds of ppl here.
digital
Cold air intake/TB spacer/8.5mm MSD wires/MSD blaster 2/Autolite 3923/Borg-warner cap and rotor/crankcase breather/Toyo proxes s/t 275/60/15/catco hi-flow cat/custom dual straight pipes/stage 2 jet chip/ 180 t-stat/50 shot NOS :)/relocated IAT sensor/turbo in production
|
F585
Dodge Dakota
JOIN HERE
7/24/2003
07:17:54
| RE: mods
IP: Logged
Message:
Sorry got confused between the two my bad!
|
00dakota
Dodge Dakota
JOIN HERE
7/24/2003
22:48:44
| RE: mods
IP: Logged
Message:
thanx
|
J and J Auto
Dodge Dakota
JOIN HERE
7/25/2003
02:24:04
| RE: mods
IP: Logged
Message:
Gates or stant 180 thermo heavy duty auto store
http://store.summitracing.com/
K&N FIPK cold air setup
Black Magic BM150 Flexolite fan 2800cfm
JBA Headers with a Dynomax 17748 with 2.5 tail
MSD 8.5 super conductor wires
ASE CHIP not cheap before I would get the chip
I would also add a F&B 48mm and the 1.7 crower
roller rockers you will benefit more from it
after these mods.
http://www.asechips.com/
Or you could just get totally carried away, mod the
intake, port the heads and stroke it,
Very Expensive I know I did it but I love the power
1.20 in the morn cant fall asleep tonight don't want
to wake the old lady so I came here to give you
guys a hard time.
Larry
J&J Auto
|
TheBigJoe
Dodge Dakota
JOIN HERE
7/26/2003
03:34:36
| RE: mods
IP: Logged
Message:
I tried stroking mine, but there was no difference..... should I rub it hard or soft. I seem to get better throttle response from yelling though.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
