| From | Message |
Matt
Dodge Dakota
JOIN HERE
11/13/2003
22:39:05
|
 Subject: RE: IAT SENSOR--IAT
IP: Logged
Message:
Since speedtweaks seems to no longer be in existance, is there another place that sells IAT adjustors?
|
Buck
Dodge Dakota
JOIN HERE
11/14/2003
07:13:35
| RE: IAT SENSOR--IAT
IP: Logged
Message:
I built my own. Here is a link I found
http://home.earthlink.net/~rpkast/IAT%20Adjuster/
Buck
|
Matt
Dodge Dakota
JOIN HERE
11/14/2003
11:49:30
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Where did you get all your parts. I assume the switches and resistors can be found at radio shack. Also, does anyone know how the IAT works? I assume it's just a theresistor. Does resistance increase with temp like normal? What are the ranges and calibration points?
|
J and J Auto
GenII
11/14/2003
12:33:29
| RE: IAT SENSOR--IAT
IP: Logged
Message:
You can buy all the parts from radio shack
a 1k ohm resistor #271-1321 5 pck
a 50k pot #271-1716
a rocker switch #275-691
a project box #270-1801
No they do not change with heat they stay where
you put them
Here is a table you can use to calibrate the
adjustor
http://www.dodgedakota.net/boards/v6/6150.html
telling the computer there is colder air will
advance the timing and dump more fuel
Larry
J&J Auto
|
Matt
Dodge Dakota
JOIN HERE
11/14/2003
12:55:09
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Do you happen to know if I can get both male and female plugs that match those on the IAT, so I can avoid cutting and splicing as well?
|
J and J Auto
GenII
11/14/2003
19:24:37
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Yes check at radio shack they have plugs and
connectors that will work
Larry
J&J Auto
|
ClassicalGas
Dodge Dakota
JOIN HERE
11/17/2003
08:22:20
|  RE: IAT SENSOR--IAT
IP: Logged
Message:
I believe the IAT adjustor kits are available from www.nextlevelracing.com. You can get a "Stage 1" or "Stage 2" kit. A bit spendie, but you just cut the IAT sensor wire, crimp the supplied connectors, plug it in and drive away...
|
J and J Auto
GenII
11/17/2003
12:05:27
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Relocating the IAT and doing the crank sensor mod
will give you the same effect.
Price, your time
Larry
J&J Auto
|
Jeff
Dodge Dakota
JOIN HERE
3/15/2004
18:36:47
|  RE: IAT SENSOR--IAT
IP: Logged
Message:
You can try Hurricane-Horsepower.com
if you just want one you don't have to build.
If you put in the adjustable versions it will track temperature with the offset selected.
|
tndak
Dodge Dakota
JOIN HERE
3/16/2004
10:28:43
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Larry,
You say that the IAT relocate and crank sensor mod do the same. Will it hurt, help or waste time to do both?
Thanks
|
read
Dodge Dakota
JOIN HERE
3/16/2004
11:03:37
| RE: IAT SENSOR--IAT
IP: Logged
Message:
tndzk:
reread Larry's post he is saying to do both mods.
|
TNDAK
Dodge Dakota
JOIN HERE
3/16/2004
12:14:19
| RE: IAT SENSOR--IAT
IP: Logged
Message:
well this just proves i should have put my contacts in before reading!!
Thanks again
|
bump
Dodge Dakota
JOIN HERE
4/21/2004
11:34:18
| RE: IAT SENSOR--IAT
IP: Logged
Message:
Good info..
|
gizmo
Dodge Dakota
JOIN HERE
7/01/2005
19:25:54
| hard starting
IP: Logged
Message:
I have a 1996 4x4 dakota with a 3.9 automatic. The truck seems to work ok, but it is hard to start when it is cold. It starts ok when its warmed up. I replaced the plug wires, plugs, distributor cap,rotor button and replaced the IAC. Any help would be appreciated. Thanks.
|
| | <<Oringinal Post <<Previous Page P 2 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
