| From | Message |
daveshotdako
GenIII
 
10/13/2005
15:14:32
|
 Subject: in need of a pre '95 v6 tb
IP: Logged
Message:
i am in need of a pre '95 v6 EGR tb to mod for someone. if anyone has one that they are willing to part with, let me know. i will pay a resonable price for one. my e-mail is davethomas2184@yahoo.com. thanks.
GET IN, SIT DOWN, SHUTUP, AND HOLD ON
|
93dak4x4
Dodge Dakota
JOIN HERE
10/13/2005
17:12:41
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
I've got my stock 93 tb if you are truly interested, I will be going home in two weeks so getting it is not a big problem. Let me know if you are interested.
|
daveshotdako
GenIII
10/14/2005
12:54:55
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
you got mail
GET IN, SIT DOWN, SHUTUP, AND HOLD ON
|
Relf
Dodge Dakota
JOIN HERE
10/16/2005
21:55:07
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
Hey daveshotdako, What's different about a pre-'95 TB? I've never seen one. I've got a V6 TB from a '98 if you want it. I am also a machinist, how were you going to make new larger throttle plates? I noticed that the periphery of the plates are slanted and are not perpendicular to the face. Tell me how to set it up, for a manual machinist. Thanks.
Relf.
|
daveshotdako
GenIII
10/17/2005
09:57:29
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
the only difference in a '95 and earlier tb is that they have EGR. other than that, they are identicle. do some careful measurements on the original plates, and you will find that the holes are .030 off of center and ther are small flats on the sides to prevent rubbing on the bearings. when i make them, i set it up on the cnc mill and mill the flats and drill the holes. then i go to the lathe and part them off. the angle is not important. you will also need to drill out the cover over the idle adjustment screw so that you can adjust it once you put it on your truck. 46mm is as big as you can bore it unless you remove the bearings and make some alluminum spacers to press in and then put the bearings in. if you do not do this and try to bore it to 48mm, you will run into the bearings. le me know if you have any more questions.
GET IN, SIT DOWN, SHUTUP, AND HOLD ON
|
N56629
Dodge Dakota
JOIN HERE
10/17/2005
12:58:38
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
I have one new body I would sell for $50. It is disassembled and will include all parts except sensors.
|
daveshotdako
GenIII
10/17/2005
14:58:33
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
what year is if off of?
GET IN, SIT DOWN, SHUTUP, AND HOLD ON
|
N56629
Dodge Dakota
JOIN HERE
10/17/2005
15:24:21
| RE: in need of a pre '95 v6 tb
IP: Logged
Message:
Not sure. It is part number 12R10897B. AFAIK it fits all EGR type magnum v6's.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
