| From | Message |
chris
Dodge Dakota
JOIN HERE
12/18/2004
21:18:29
|
 Subject: rocker swap/1.7s 4 sale
IP: Logged
Message:
Selling truck a v6 2001 have had 1.7 harland sharp roller rockers for about 1000k great mod.
I want to put back in stock rockers can anyone help with proper procedure. 1.7s 4 sale $200.00us shipped to anyone interested way more new!
Chris
|
JFH
GenII
12/18/2004
22:34:46
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
You've got mail
http://www.cardomain.com/memberpage/546400
|
Moe
Dodge Dakota
JOIN HERE
12/18/2004
23:15:57
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
Chris- I have '01 V6 and this would be a good 100% fit. Here my email address "garde01@comcast.net". What do you think the labor cost if I have a shop do the installation?
Moe
|
chris
Dodge Dakota
JOIN HERE
12/19/2004
16:20:18
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
these are a simple 2hr tops bolt on. drop them in and torque to 20-21 ft/lbs. if you can change a tire you can install the harland sharps.
|
wadak
GenIII
12/19/2004
19:31:24
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
I have 2 daks, I have the Harland Sharp in one dak and the Crower in the other. The Harland sharp's are much easier to install as stated above, no modification needed to the valve covers. I have the crowers in the other dak you must bring each cylinder up to top dead center to install, tightem down till you get zero turning oon the push rod as you move it back and forth with your fingers then 1/2 to 3/4 of turn beyond that on the adjusting nut then using an allen wrench to tighten down the sure-locks. You follow thsame prcedure on each cylinder, then the baffles inside each valve cover must have the baffles "knocked down" about 3/8 of an inch to fit over top of the rockers. The Crowers are more difficult to install. It took about 3hrs for the Crower RR's and about an hour for the Harland Sharps. Are the Harland Sharps better than the Crowers? Thats a question I can't answer yet. I did put 6000 miles on the dak the with HS rr. They were installed on the truck when it had close to 100,000 miles and so far no problems.
92 and 97 Daks both with many mods.
|
moe
Dodge Dakota
JOIN HERE
12/21/2004
10:15:34
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
Wadak - How much HP/Torque did you gain after you installed the HS 1.7RR?
My Truck has the following mods: 3" BL, BFG 31x10.5 MTs, JBL headers, Magnaflow single exhaust, Air aid intake, Jet II, AP3923 spar plug, MSD cable and 180 degree thermostat.
Adding this 1.7RR along with the mods I have, how gain would I get? Anyone could give an approximate gain, I would appreciated.
Thanks,
Moe
|
Wadak
GenIII
12/21/2004
12:19:15
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
According to Larry from J and J Auto the 1.7 roller rockers add 15 to 17 hp., definitely a noticeable increase in power.
92 and 97 Daks both with many mods.
|
Big Will
Dodge Dakota
JOIN HERE
12/22/2004
15:47:09
|  RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
Who sells the Harland Sharps retail?
All your advice is greatly appreciated.
|
wadak
GenIII
12/22/2004
23:44:41
| RE: rocker swap/1.7s 4 sale
IP: Logged
Message:
http://www.southeastrt.com/ John at southeast sells them the information is at his web site.
92 and 97 Daks both with many mods.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
