| From | Message |
Moe
Dodge Dakota
JOIN HERE
10/30/2004
13:26:37
|
 Subject: Engine Light came on
IP: Logged
Message:
Few days ago, I increased the gap of the 2393 autolite spar plugs from .050 to .060. Notice a power gain and it's great. Last night driving home, the engine light came on. The engine light was never came on before.
Any feed back, greatly appreciated.
2001 v6 with these mods: F/S 48mm TB, JBL headers, Magnaflow single exhaust, Jett II and MSD 8mm plug cables and Air raid air intake.
Thanks,
Moe
|
daffydak
GenIII
10/30/2004
14:12:15
|  RE: Engine Light came on
IP: Logged
Message:
it might be a code for random misfire. assuming you still have a stock coil/ign system. it may not be able to put out enough power for that big of a gap..
Try this to get the code(s) It does not work on all dakotas, it did not work on my 98 but it works on my 00.
Without cranking the truck turn the key like this....
after the first click of the igniton switch (the steering columun unlock positon, where the {P R N D 2 1} gear selector illuminates and you can move the shift lever)
Like this;
on/off/on/off/on
then in your odomiter it will say the code(s) It says P-DONE if there aren't any codes, or after they are all listed... the code will come up like thos P0300 is random misfire. 301 through 308 (306 on a v6) is for misfinring in a specific cylinder (PO303 = misfire cylinder#3)
hope I helped
post the code here, and I (or someone else) will look it up for you....
00 CC Sport Plus 4.7L 4X4 Auto, 3:55 LSD
Flowmaster orig. 40 series (2 chamber) muffler, adjusted tps to .76V, ported TB, home brew intake setup w/K&N filter, more mods to come!!!
Dan
MOPAR=More Power!!
|
Moe
Dodge Dakota
JOIN HERE
11/01/2004
10:08:31
|  RE: Engine Light came on
IP: Logged
Message:
Dan - Thanks for your input. Did a search of this issue and most of them reset PCM by disconnecting the - cable battery and PCM connector plug. I did the samething with my truck and engine light is NOT there anymore.
Hope engine light do not come on anymore. But if it does, I will do what you said.
Thanks,
Moe
|
GB2000
GenIII
11/01/2004
16:26:24
| RE: Engine Light came on
IP: Logged
Message:
Resetting your PCM when you get a light is normally a temporary fix...unless you fix the problem causing the light, the conditions are still there and it's just a matter of time before it goes on again.
Josh
http://www.cardomain.com/id/sentenced
|
Moe
Dodge Dakota
JOIN HERE
11/09/2004
09:58:30
| RE: Engine Light came on - HELP
IP: Logged
Message:
Dan or anyone - Engine light on and the code is P1762. If you could tell me what this code is and to fix it I greatly appreciated.
Thanks,
Moe
|
Moe
Dodge Dakota
JOIN HERE
11/09/2004
10:05:27
| RE: Engine Light came on
IP: Logged
Message:
Dan or anyone,
The engine light is on again and the code is P1762. Could anyone tell me what this code means and what I need to do to fix it.
Thanks,
Moe
|
Shepp
Dodge Dakota
JOIN HERE
11/16/2004
15:05:45
| RE: Engine Light came on
IP: Logged
Message:
P1762
GOV PRESSURE SENSOR OFFSET
Governor pressure sensor input greater than a calibration limit or less
than a calibration limit for 3 consecutive park/neutral calibrations
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
