| From | Message |
2KV6AUTO
Dodge Dakota
JOIN HERE
2/12/2002
19:13:51
|
 Subject: Foglight install info needed
IP: Logged
Message:
I got a 2K Dakota and it didnt come with the foglights and the foglight valence. I was thinking of getting an OEM replacement valence. What kind of mounts do I need? Where can I get them and about how much do they run? Ive heard you can tap into the existing wiring on the truck even though it didnt come with the lights. I think I need a relay. How do I go about doing this and has anyone had any experience with donig this. Any info is greatly appreciated. Thanks
|
Nick
Dodge Dakota
JOIN HERE
2/13/2002
01:06:51
|  RE: Foglight install info needed
IP: Logged
Message:
You can buy the foglights and wiring harness from the dealer for I think about $160. I bought a set from www.autobarn.com for $60 that comes with a wiring harness and a switch you can mount under the dash. The Diamond Blue Round Light Kit includes the wires, switches and connectors to provide your vehicle with a light that projects a whiter, brighter light for superior visibility! The computer modeled reflector uses entire surface area to project light, making the reflector 98.5% efficient compared to the conventional 50%. The unique optic free "blue" glass provides a whiter, brighter more defined beam pattern for maximum visibility. Kit comes with two (2) H-3/55W lamps that meet SAE requirements.
|
Brian Fabian
Dodge Dakota
JOIN HERE
2/13/2002
03:39:48
|  RE: Foglight install info needed
IP: Logged
Message:
I also have no foglights and I was wondering how to go about putting the foglights in the factory holes? How do I cut out the holes safely without screwing up?
|
Dakota/cali
Dodge Dakota
JOIN HERE
2/13/2002
15:12:22
| RE: Foglight install info needed
IP: Logged
Message:
Just put mine on went to local shop and got oem spec replacements 40 dollars.then bought ultra white bulbs 20 bucks and monted them directly of bumper using a small piece of flat bar with to wholes
|
BB2DAK
Dodge Dakota
JOIN HERE
2/13/2002
15:22:39
| RE: Foglight install info needed
IP: Logged
Message:
I installed these on my Dakota.
Pilot PILPL119X $80.00 for clear
$85.00 for blue or amber
http://www.autoaccessory.com/cgi-bin/ncommerce3/ExecMacro/product/AutoAccessorycom/prod2frame.d2w/report?prrfnbr=46677&prmenbr=402
I installed them with the aftermarket switch mounted just left of the steering wheel.
2001 Quad Cab SLT+ 4.7L 5-Speed 3.55 Lslip
ARE Cap, ArmaCoat Bed-liner, Pilot PILPL119X Fog Lights
Autolite 3923's, IAT Adjuster, K&N Drop-in w/modified intake
http://members.aol.com/bsbets/truck/intake4.jpg
http://www.dodgedakota.net/albums/viewer/101.htm
|
Bill
Dodge Dakota
JOIN HERE
2/13/2002
16:17:07
| RE: Foglight install info needed
IP: Logged
Message:
I just got some Pilot foglights for my 2001 Dakota.
Brian,
You will want to measure the hole first, it should be a 4" hole (that's what mine was). I got a 4" hole saw and put it in my cordless drill and just drilled right throuhg the valence. I cleaned up the edges with a Dremel tool. You can check out pics of the install on my website.
Bill
http://members.aol.com/btaylor04/BTruck.html
|
2KV6AUTO
Dodge Dakota
JOIN HERE
2/13/2002
17:33:20
| RE: Foglight install info needed
IP: Logged
Message:
So where can I get the foglight mounts from and how much
|
Bill
Dodge Dakota
JOIN HERE
2/13/2002
17:38:22
| RE: Foglight install info needed
IP: Logged
Message:
The lights I got had mounting brackets already on them. The only thing I had to get was electrical box mounting brackets (see the photo on my website) which I got at the local hardware store for really cheap, a few bucks at the most. I think you will need to pick out a set of lights and see what they come with and go from there and just play around with them. I had to experiment a few times to get things just the way I wanted them.
Bill
http://members.aol.com/btaylor04/BTruck.html
|
BB2DAK
Dodge Dakota
JOIN HERE
2/14/2002
09:30:36
|  RE: Foglight install info needed
IP: Logged
Message:
The foglight that I installed, Pilot PILPL119X is a kit that is made for
the Dakota. They came with mounting brackets, and
the install was very easy. To install the lights,
I used a utility knife, and cut the valence as close to round as I could.
I then used a dremel tool with a sanding wheel to smooth out the edges.
I mounted the relay in the engine compartment on a battery tray screw, then ran the wire inside
and have it connected to the fuse block so that I have power when the key is on.
The switch is mounted to the left of the steering wheel.
The lights are very bright, and I am happy with the install. One annoying item was that the power wires for the lights are white. I spent a few bucks, and covered the wires with black plastic wire tubing. The black looks better in the engine compartment.
http://www.autoaccessory.com/cgi-bin/ncommerce3/ExecMacro/product/AutoAccessorycom/prod2frame.d2w/report?prrfnbr=46677&prmenbr=402
2001 Quad Cab SLT+ 4.7L 5-Speed 3.55 Lslip
ARE Cap, ArmaCoat Bed-liner, Pilot PILPL119X Fog Lights
Autolite 3923's, IAT Adjuster, K&N Drop-in w/modified intake
http://members.aol.com/bsbets/truck/intake4.jpg
http://www.dodgedakota.net/albums/viewer/101.htm
|
Bill
Dodge Dakota
JOIN HERE
2/14/2002
09:40:05
| RE: Foglight install info needed
IP: Logged
Message:
Your installation sounds similar to mine. I too got Pilots, but not that same model number, but they work just fine in my Dak, except I had to make the slight mods i spoke of earlier with the mounting. I would recommend Pilots to anyone.
P.S. I did have one light burn out already. Just went down to the local AutoZone and picked up a set of H3 bulbs and replaced it in about 5 minutes.
Bill
http://members.aol.com/btaylor04/BTruck.html
|
kevster
Dodge Dakota
JOIN HERE
2/16/2002
19:04:10
| RE: Foglight install info needed
IP: Logged
Message:
I have the wire harness from the factory for the fog lamps, comes with relay and inline fuse.. all connectors, NEW.. Never used, will sell for 45.00 includes the shipping.and comes with instructions.
|
Lesley
GenIII
2/16/2002
20:23:43
| RE: Foglight install info needed
IP: Logged
Message:
I bought two sets off ebay, both sets are complete. One set listed as Dakota Durango Driving Lights, the other were Dakota Ultra Fog Lights. I got them for $75 & $98 respectively, I'll keep whichever set I like better when they get here, and the other set is promised to a Durango friend.
97 3.9 CC Sport. Black. Auto 3.55
Quick D Intake, JBA Stainless headers, Autolite 3923s, stainless Borla Turbo XL, V8 R/T TB,
19 lb.FMS fuel injectors. Coming 17" Boyd Coddington Smoothies
|
Marks DQC
GenIII
2/16/2002
20:38:26
| RE: Foglight install info needed
IP: Logged
Message:
FYI I just put my lower valence, with fog light holes up for sale on ebay.
Lower Valence on eBay
2001 Dakota Quad Cab SLT , 4.7L, Auto, 3.55 LSD, Garnet Red over Slate, Zaino, Tint, Vent Guard, Gaylords Lid, Hotchkis Springs, Bilstein Shocks, Wet Okole Covers
|
Wcomea
Dodge Dakota
JOIN HERE
3/15/2002
11:27:54
| RE: Foglight install info needed
IP: Logged
Message:
Bill did you have to drill any additional holes through the fire wall or were you able to piggy back on an existing wiring harness?
|
Lesley
GenIII
3/15/2002
11:39:14
| RE: Foglight install info needed
IP: Logged
Message:
I have a set of ultra bright fogs, complete kit with harness, brackets and switch. I decided to keep the softer beam set. I paid $97 for them, make me an offer!
97 3.9 CC Sport. Black. Auto 3.55
Quick D Intake, JBA Stainless headers, Autolite 3923s, stainless Borla Turbo XL, V8 R/T TB,
19 lb.FMS fuel injectors. Coming 17" Boyd Coddington Smoothies
|
Bill
Dodge Dakota
JOIN HERE
3/15/2002
13:54:49
| RE: Foglight install info needed
IP: Logged
Message:
Wcomea,
I did not to any drilling in the firewall. I am not 100% sure (it has been a while and I can't run out and look at my truck at this moment) but I think I ran the wiring right up next to the sheetmetal and up through to the fush box. It took some time to fish everything through, but it can be done. If you go to the driver's side of the master cylinder right up by the sheet metal you can fish the wires through up by the fuse panel. I hooked it up to a fuse that only gets power when the key is turned so I don't forget to shut them off and drain my battery. Hope that helps.
Bill
http://members.aol.com/btaylor04/BTruck.html
|
Lesley
GenIII
3/15/2002
21:56:05
| RE: Foglight install info needed
IP: Logged
Message:
I got mine in today, they look GREAT! If your air dam is like mine, it would be easier to use a 4" hole saw to prepare the holes.
97 3.9 CC Sport. Black. Auto 3.55
Quick D Intake, JBA Stainless headers, Autolite 3923s, stainless Borla Turbo XL, V8 R/T TB,
19 lb.FMS fuel injectors. Coming 17" Boyd Coddington Smoothies
|
Chiliedude
Dodge Dakota
JOIN HERE
3/16/2002
12:29:37
| RE: Foglight install info needed
IP: Logged
Message:
My CC did not come with them either, so i got them from this web site, very easy to install, comes with everything u need mounts and all. https://www.dodge-parts.net/index.asp
Darren
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
