From | Message |
Sledge Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
7/31/2004 14:55:58
|
Subject: TPS Change voltage with TB Swap? IP: Logged
Message: All-
I am going to test my TPS sensor and see how the voltage is. If it is low I want to adjust it by doing the mod. My only question is:
At the moment I have my stock TB. I plan to buy an upgraded Throttle Body (F&B 48MM) within 5 months. Will this affect the voltage in any way if I trade Throttle Body's?
Thanks
Sledge
|
Black 97 Dodge Dakota JOIN HERE
7/31/2004 15:45:16
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: The only way the voltage is changed is by movement of the TB blades. It will be slightly different just from on TB to the next TB, but nothing drastic. If you need to, you can change the 'at idle' voltage by the following.
Applies to the 5.2/5.9 and I believe the 3.9
I do not know about the 4.7. These steps are after the TB is installed on your engine.
-Remove the 2 metal inserts that the bolts go though to scrure the TPS to the TB. One on each side. You can use a drill bit and heat up the instert to cause it to come out.
-Initially install the TPS snug (snug enough so you can barely move the TPS) Remember that you will need a flat washer between the screw and TPS now, b/c of the hole size.
-Plug in the TPS wire harness
-Back probe the wire harness with a mulit-meter
-Turn the ignition on (battery must be connected)
-Most people say to set it anywhere from .65v to .80 volts. Factory is from .45v? to .65?, I believe.
-To set it, rotate the TPS until you get the desired voltage.
-After you find the setting you like, tighten down the TPS.
-Project completed. (Don't forget to reattach anything you may have removed to get to this point.
By setting the volts closer to 1.0v, the throttle response is quicker, i.e. less hesitation upon initial throttle movement.
I did have mine set at .75-.78v, but have returned it back to .61-.63v. A little too quick throttle response in my opinion.
|
jim Dodge Dakota JOIN HERE ![Email](http://www.dodgedakota.net/amb/icons/email.gif)
8/01/2004 05:35:46
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: will you send me pic if you can and ins.
email jhinson1216@hotmail.com
|
Black 97 Dodge Dakota JOIN HERE
8/01/2004 20:31:55
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: I do not have pics of it, I can make some for you sometime this week and post them on my bud's website. Let me talk with him and see about setting it up on Tues or Wednesday.
|
blackrtaz Dodge Dakota JOIN HERE
8/03/2004 18:49:58
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: I am also interested in this project... Let me know what the website is when you post up the pics... thx
|
ScojoDak Dodge Dakota JOIN HERE
8/04/2004 09:41:45
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: Isn't there three wires at the TPS plug? If so, which ones do we check?
|
? Dodge Dakota JOIN HERE
8/04/2004 13:09:15
| RE: TPS Change voltage with TB Swap? IP: Logged
Message: Here is some info for You..
http://www.speedtweaks.ca/tipsandtricks.php#TPS_Mod
|
| P 1 |
|
Post a reply to this message:
Username Registration: Optional All visitors are allowed to post messages
|