Forums
Forum Tools
|
 |
00:06:33 - 12/20/2024
Off Road
| From | Message |
GABE
Dodge Dakota
JOIN HERE
11/04/2004
21:17:05
|
 Subject: DRIVE SHAFT 4X4 ???
IP: Logged
Message:
I HAVE A 2001 DAKOTA 4X4, THE DRIVESHAFT TO THE FRONT OF THE TRUCK FOR THE 4WD HAS ( OR LOOKS LIKE) IT HAS A CV JOINTON THE TRANS.END OF IT. THE BOOT WENT OUT.DOES ANYONE KNOW WHAT ITS CALLED AND WHERE I CAN FIND ONE CHEEP.
THANKS FOR THE INFO
GABE
VETTE732GRANDECOM.NET
|
4x4Dak
Dodge Dakota
JOIN HERE
11/05/2004
12:51:51
|  RE: DRIVE SHAFT 4X4 ???
IP: Logged
Message:
Good luck! You can get a stock shaft or get one custom made. I had one made because the stock one is a POS. I paid $600 dollars for a custom double cardan joint type. They don't make any aftermarket shafts for our year.
http://photos.yahoo.com/dakotaqc4x4
01 Quad Cab Sport 4x4 4.7l 3.92lsd 5spd
HO Cams, Volant CAI, Flowmaster 40srs, Ported TB, Amsoil on everything, Water Wetter, 3” PA, 3” Rancho, RS9000x’s, 35” Pro Comp MT’s, 2 KC 6” 150 Watt lights on a Westin Safari Bar, Smittybilt Nerf Bars, Clear Corners, Brembo Slotted Front Rotors, Hawk Pads, 4.56 gears & Full Detroit Locker
|
DAHEMIKOTA
GenII
11/21/2004
22:25:06
| RE: DRIVE SHAFT 4X4 ???
IP: Logged
Message:
4X4Dak, Where did you get 4.56:1 gears for the Dakota front axle? I have been looking all over and the highest I can find is a 4.10:1. A couple of my buds had a shop install 4.56 gears in their 4X4s and when we checked we found that they said they put 4.56's in but they were actually 4.10's. The guy was a smart a$$ and said we wouldn't have known the differance if we didn't check.If you actually bought yours,I would like to know who can supply them. Thanks, Dan
|
4x4Dak
Dodge Dakota
JOIN HERE
11/22/2004
11:53:25
| RE: DRIVE SHAFT 4X4 ???
IP: Logged
Message:
I can't say that I have checked to see if they are 4.56's, but I can't definately feel the difference. I had the 3.92's before hand, and I don't think that I would have felt anything going to 4.10's. Anyways, they're called Driveline Vista in California. He went through alot of trouble trying to find out what type of axle we have in the front, it's an 8" American axle. Once he found out what axle I had in the front, he was able to get gears for it. I posted this shortly after I found out, but no one responded so I figured that it was old news.
http://photos.yahoo.com/dakotaqc4x4
01 Quad Cab Sport 4x4 4.7l 3.92lsd 5spd
HO Cams, Volant CAI, Flowmaster 40srs, Ported TB, Amsoil on everything, Water Wetter, 3” PA, 3” Rancho, RS9000x’s, 35” Pro Comp MT’s, 2 KC 6” 150 Watt lights on a Westin Safari Bar, Smittybilt Nerf Bars, Clear Corners, Brembo Slotted Front Rotors, Hawk Pads, 4.56 gears & Full Detroit Locker
|
DAHEMIKOTA
GenII
11/23/2004
00:11:15
| RE: DRIVE SHAFT 4X4 ???
IP: Logged
Message:
Thanks,4X4Dak, I will check them out. I stuck an 8 3/4" rear in my truck and it has 4.56:1 gears. My front end has 3.55:1 gears. Had to take the driveshaft out so I wouldn't forget and put it in 4WD and bust everything. I'm just too cheap to buy new gears for the rear end. Dan
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
|
