Forums
Forum Tools
|
 |
00:27:44 - 12/20/2024
General Dakota Board
| From | Message |
Rob
GenIII
9/03/2002
16:50:29
|
 Subject: Sad Sad and MAD
IP: Logged
Message:
I just ran up to the store and I was driving down the road and next thing you know I am dodging a piece of assphalt on the road.I tryed to miss it butt it clipped my rim.NASTY SCRATCHES and it really pisses me off.It looks all most as bad as a curbed rim.
Anybody got suggestions on how to remove deep scratches on BOYDS? by the way it only scratched the hoop so I guess the last resort would be to rehoop the rim!
1NICEDAK
|
3
Dodge Dakota
JOIN HERE
9/03/2002
19:31:11
|  RE: Sad Sad and MAD
IP: Logged
Message:
3
|
Bob W
GenIII
9/03/2002
20:29:59
|  RE: Sad Sad and MAD
IP: Logged
Message:
3?
Gibson headers, Gibson Cat-back, Edelbrock IAS shocks, K & N drop in, 180 stat, Jet stage II chip, ARE Lid
|
Lesley
GenIII
9/03/2002
20:51:34
| RE: Sad Sad and MAD
IP: Logged
Message:
I can sympathize. I had my Boyds on for about 48 hours when I had to swerve to avoid an old couple that were drifting into my lane. I gouged one of them pretty badly on the curb. Apparently they can be polished out, but it isn't cheap. I'm going to wait until I take them off for winter.
97 3.9 CC Sport. Black. Auto 3.55, Quick D Intake, JBA Stainless headers, Autolite 3923s, stainless Borla Turbo XL & tip, V8 TB, FMS 19 lb fuel injectors, 17x10 Boyd Smoothies, JBA 9mm cables, Lakewood chrome traction bars. Have, but not installed: 3.92s, Infinity Sound System
|
kota on 20s
GenIII
9/04/2002
01:00:20
| RE: Sad Sad and MAD
IP: Logged
Message:
Rob, dont worry. sand paper will take it out. i know it sounds harsh, but it works. start with a rough grit (depending on how bad the scratch is, you will have to start with a lower grade paper) and work your way down to wet and dry 600 grit.
after it is smooth, use some polish like mothers, and polish it to a mirror finish.
good luck
-Eric
Injection is nice, but i'd rather be blown.
5.2L, 5speed. Powerdyne SC, 50mm TB, 2bbl M-1, 1.7RR's, MSD 6BTM, ciramic JBA headers, carsound cat, dumped gibson
|
Rob
GenIII
9/04/2002
11:49:02
| RE: Sad Sad and MAD
IP: Logged
Message:
Thank you.I heard about the sanding then polishing method I think i will try that!
1NICEDAK
|
Lesley
GenIII
9/04/2002
12:17:31
| RE: Sad Sad and MAD
IP: Logged
Message:
I thought about that too - especially after seeing what a great job intense99 Chuck did on the aluminum parts in his engine bay - and mostly using sandpaper. I haven't been brave enough to try it though. Let me know how it works out Rob. :)
97 3.9 CC Sport. Black. Auto 3.55, Quick D Intake, JBA Stainless headers, Autolite 3923s, stainless Borla Turbo XL & tip, V8 TB, FMS 19 lb fuel injectors, 17x10 Boyd Smoothies, JBA 9mm cables, Lakewood chrome traction bars. Have, but not installed: 3.92s, Infinity Sound System
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
|
