| From | Message |
anthony
Dodge Dakota
JOIN HERE
7/10/2011
05:21:10
|
 Subject: RE: Clutch adjustment?
IP: Logged
Message:
i have a 2003 dodge Dakota 3.9l and i have the same
problem with michaelaflore posted on 4/28/2010
20:05:22 when i put it into first and second gear it
will kick back out, so i replace the master, slave,
release bearing, clutch and pressure plate but no
luck, Any help is appreciated thank you
|
yeah
Dodge Dakota
JOIN HERE
7/10/2011
10:12:49
|  RE: Clutch adjustment?
IP: Logged
Message:
Worn dogs or syncros.........
|
tony
Dodge Dakota
JOIN HERE
10/16/2011
17:28:02
| RE: Clutch adjustment?
IP: Logged
Message:
i have a 97 dakota with a 2.5 4 banger in it.i just put a another tranny in it and also a m/c and s/c.theres no bleeder valve on the s/c.how do i prime it up?
|
Juliet K
Dodge Dakota
JOIN HERE
10/22/2011
20:34:22
|  RE: Clutch adjustment? (95 Dakota V8-5L-Manual)
IP: Logged
Message:
I think my clutch is shot! my partner was trying to back up a loaded hauling trailer--up a small hill--and all I could hear is loud and long grinding! That was about 3 weeks ago. I have lately felt the clutch "losing it's grip". I was just going to get a clutch kit from Napa and replace it. However, after reading some of the posts here, I am starting to think that I may still have trouble even after the R&R. Anything else, my people?
|
andy A-K-
Dodge Dakota
JOIN HERE
10/29/2011
16:35:51
| RE: Clutch adjustment?
IP: Logged
Message:
it's better to start with the easiest solution. Check the fluid level, pedal free play, any leaks from the master cylinder/slave cylinder, mechanical connections, etc. If everything looks OK, then you can take apart the transmission and clutch. Then you need to check the bearings, friction disc, pressure plate, gears, synchros, detent mechanisms and all other parts. Then when you find the worn parts, you can order the parts and replace them. It's probably a good idea to replace all the bearings and lightly worn parts, too, even though you don't really have to.
|
jabogle
Dodge Dakota
JOIN HERE
1/23/2012
21:15:00
| RE: Clutch adjustment?
IP: Logged
Message:
Hello,
I have a 1995 Dodge Dakota Sport 2.5L 4 cylinder manual transmission. My truck made a grinding noise and a slight pop while I was driving it in 4th gear. It now acts as if it's in neutral and when put into gear it just revs the engine and doesn't go anywhere. Can anyone help me with the solution to this problem?
Thank you in advance.
|
Clutchweird
Dodge Dakota
JOIN HERE
2/14/2012
10:34:23
| RE: Clutch adjustment?
IP: Logged
Message:
I just had my clutch replaced. When pulling out the transmission they discovered a bad input shaft bearing. Sent out to a transmission shop that replaced input shaft, mainshaft bearing, front & rear seals & said all else was good. Reinstalled with new clutch kit & cut fly wheel. When I got the truck back the clutch grabs about 1/2 inch off floor & can't start off without shaking. Any help would be appreciated. Dodge Dakota 2004 5 speed with about 100,000 miles.
|
Mike garrels
Dodge Dakota
JOIN HERE
6/20/2012
15:02:07
| RE: Clutch adjustment?
IP: Logged
Message:
2004 Dakota 4.7 4wd 5 spd
Truck would not go in to gear. Mechanic replaced clutch with clutch kit and it was fine, several days later would not go in gear again. Replaced clutch cylinders with kit,ok for several days then would not go into gear again. In order to back out of garage engine must be off to put in gear. Any solutions????
|
Tracy
Dodge Dakota
JOIN HERE
3/10/2015
19:50:42
|  RE: 1998 Dodge Dakota 5 speed will not shift
IP: Logged
Message:
My truck is a Dakota sport , today I was stopped went to put it
in 1st and I could not get it into gear unless It was moving ant
idea
|
grjms4ever@gm
Dodge Dakota
JOIN HERE
4/30/2015
18:32:55
| RE: Clutch adjustment?
IP: Logged
Message:
Well i just replace the clutch on a 2002 dakota 3.9
And blead all the lines.but the truck still won't go
into gears the pedal it's all do way to the top?
Please help
|
grjms4ever@gm
Dodge Dakota
JOIN HERE
4/30/2015
18:36:19
| RE: Clutch adjustment?
IP: Logged
Message:
Well i just replace the clutch on a 2002 dakota 3.9
And blead all the lines.but the truck still won't go
into gears the pedal it's all do way to the top?
Please help
|
me
Dodge Dakota
JOIN HERE
5/25/2015
07:34:47
| RE: Clutch adjustment?
IP: Logged
Message:
Mhy Throwout bearing obliterated at 180,000
Cost 1000 to have new clutch/throwout bearing
Pressure plated installed
|
| | <<Original Post <<Previous Page P 2 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
