Dodge Dakota ForumDodge Dakota PhotosDodgeDakota.net Membership
  Forums   Forum Tools
01:21:39 - 12/20/2024

General Dakota Board
FromMessage
Bill H.
Dodge Dakota
JOIN HERE
 Email

4/14/2006
17:18:19

Subject: Steering bushings
IP: Logged

Message:
I've had a clunking in the front end when the steering is taken to the limit lock in each direction for a few weeks and finally narrowed it down to the bushings where the steering gear (rack and pinion?) attaches to the frame and front drive axle housing. Has anyone had to changed these bushings before? How difficult is it? It almost looks as if you have to drop the axle down to get to them.

If it's not one thing it another!!!



nick01
Dodge Dakota
JOIN HERE


4/14/2006
17:52:31

RE: Steering bushings
IP: Logged

Message:
How could any Dodge owner have missed that chapter? Oh crap.... there went my tire!!!

If your under 100k take it to the dealer. It's a recall.



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/14/2006
19:09:13

RE: Steering bushings
IP: Logged

Message:
Nick, I must have been sleeping when that recall went out. Mine has 150K on it. Both are shot to hell. I take it by your answer that it is quite involved???



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/14/2006
19:27:29

RE: Steering bushings
IP: Logged

Message:
Nick, I just checked the recall web site that lists all the recalls for a particular make/model etc. and found nothing in regards to the rack and pinion steering mounting bushings. Are you able to provide a campain #??? so I can research this better?



Nick01
Dodge Dakota
JOIN HERE


4/14/2006
20:05:19

RE: Steering bushings
IP: Logged

Message:
I'm not sure how involved it really is.. I didn't get involved (pun intended).

I'll see if I can get something off my paperwork. I know the mech at the dealer said something about doing over 30 trucks in last two weeks before I got mine done. (about 2 years ago).

I'll see what I can find for you.



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/14/2006
20:14:33

RE: Steering bushings
IP: Logged

Message:
That would be a big help Nick. Thank you. Just looking at it I don't think it is going to be too much fun. I just replaced both half shafts and intermediate shafts. That was fairly easy. The home made slide hammer was some what questionable but it did the job. I'm sure any onlookers would have surely laughed as it looked a lot like Joesh!t the rag man under the largest shade tree available ;^)



nick01
Dodge Dakota
JOIN HERE


4/14/2006
21:29:05

RE: Steering bushings
IP: Logged

Message:
I just went though my filing cabinet and I don't see any paperwork. All I found was when the replaced my cat converter under warranty. I did find some paperwork on camp no. 04V596000. I sure I had this work done too. You may want to check up on it.

I know it's around (just moved so things are little shuffled right now)just got to find it.

Check back in the next day or so and I'll post when I find it.



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/14/2006
21:54:09

RE: Steering bushings
IP: Logged

Message:
Thanks



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/15/2006
11:30:35

RE: Steering bushings
IP: Logged

Message:
04V596000 is the upper ball joint recall. I'm still looking.



daddio
Dodge Dakota
JOIN HERE
 Email

4/15/2006
12:05:12

RE: Steering bushings
IP: Logged

Message:
Bill H., you can go to www.dodge.com and on their webpage there is a section to check on recalls for your particular vehicle. it requires the last 7 or 8 digits of your VIN. it may help.




Obio3
Dodge Dakota
JOIN HERE


4/15/2006
14:47:05

RE: Steering bushings
IP: Logged

Message:
Any chance NICK is getting this problem mixed up with ball joints ?? I've searched recalls a lot on all crysler products and seen nothing about steering or rack a pinion bushings.

So many problems .... So little time



Bill H.
Dodge Dakota
JOIN HERE
 Email

4/15/2006
16:39:19

RE: Steering bushings
IP: Logged

Message:
Daddio, I checked the Dodge site and ran it by the last eight of the VIN. No outstanding recalls for my truck.

I took a better look at it this morning and it really appears as if the front axle will have to be dropped in order to change the bushings. That sucks! Oh well, next months project has now been planned for me.



   P 1


Post a reply to this message:

Username Registration: Optional
All visitors are allowed to post messages


Name:
Email:
Notify me when I get a reply to my message:Yes  No

Icons:            

          

Subject:
Message:
 



Home | Forums | Members | Pictures | Contact Us

This site is in no way affiliated with Chrysler or any of its subsidiaries.