| From | Message |
chris
Dodge Dakota
JOIN HERE
8/10/2006
15:43:55
|
 Subject: RE: Kicker L7's
IP: Logged
Message:
^^^^^^^^^^^^^^^^^^^^^^^and how would i do that and how much would it cost??because i dont have the money to get other amps...i have a pioneer deh-p3600 cd player 3 band parametric equalizer and dual preouts sub woffer drive capabilty thats what it say's on the box anyways. but yeah would i beable to hook up two 12 inch l7's to my two alpine t707's?
|
chris
Dodge Dakota
JOIN HERE
8/10/2006
16:07:46
|  RE: Kicker L7's
IP: Logged
Message:
be4 u said at your wonrisk why what could happen??my friends brother two kicker 15's the old round ones and the use the spliter and it worked ok for him but he blown a sub doin something on his cd player...so i think it would be okay if i did use the spliter and i did check on my amps and there is no in/out on it the only thing on mine is input ch-2 and ch-1 and speaker level input ch-2 (r)ch1 (L)and then the speaker output ch-2 and ch-1 and then bridged it has two 20A fuse's then the battery remote then the gnd and then on the other side i have the phase input mode filter crossover subsonic filter then bass EQ then the gain ans so yeah thats every thing on this anp and the other v12 i have the bother the same modle and i have a another amp that im not goin to use its a alpine v12 t500 with 300w max
|
Audiophile72
Dodge Dakota
JOIN HERE
8/11/2006
10:46:05
| RE: Kicker L7's
IP: Logged
Message:
The how I already explained. Hook the Y-cable into the sub-out on your Head Unit. That will give you two new sets of RCAs - you will run one set to each amp. You will need to run two supplies for power to the amps so you should get a distribution block. Then you will hook one sub up to each amp. If you want to get maximun power out of the amps to the drivers, I would suggest bridging each amp and run a 2 ohm to the drivers. You would need to bridge your drivers for a 2 ohm load as well since you're running 4 ohm DVC. Or, you could run the amp in 2-ch mode and wire up each voice coil to a single channel on the amp.
You could run both drivers off the one amp, but I think you would get poor performance due to lack of power.
Theoretically splitting the signal won't cause damage. I don't recommend it because 1) it's not the cleanest way to wire things up, and 2) I've never run that configuration (because it's not the cleanest) and I don't tend to recommend things I've never tried myself but I thought it necessary to throw it out there as an option. I say at your own risk because I don't need you coming back on here and chewing me out if something goes wrong with your install. : )
Another option you can consider is to hook up one sub to one amp and see if you like how it sounds. If you like it, you can sell the others and put some money in your pocket. You don't need 50 drivers in your trunk to get good bass, especially if you have a good, properly tuned enclosure. You wouldn't believe the amount of bass I've squeezed out of 2 six inch subs!
|
chris
Dodge Dakota
JOIN HERE
8/12/2006
01:25:01
|  RE: Kicker L7's
IP: Logged
Message:
okay thanx and if any thing dose go wrong im NOT goin to blame you... thanx guy you solved all my questions
|
Audiophile72
Dodge Dakota
JOIN HERE
8/14/2006
15:40:33
| RE: Kicker L7's
IP: Logged
Message:
No problem...glad to help. Let me know how you make out and what configuration you decide upon.
|
chris
Dodge Dakota
JOIN HERE
8/16/2006
03:01:37
| RE: Kicker L7's
IP: Logged
Message:
ok but it might be awhile im kinda broke at the moment... and l7's are a alot of money i was lookin on ebay and there goin 4 like 300 to 400$$ :>/
|
ANDY
Dodge Dakota
JOIN HERE
4/03/2007
02:03:47
| RE: Kicker L7's
IP: Logged
Message:
I HAVE A 350.2 KICKER AMP ON A L7 BUT WANT MORE POWER WHAT KIND OF AMP SHOLD I GET
|
Alec
Dodge Dakota
JOIN HERE
4/13/2007
01:21:35
| RE: Kicker L7's
IP: Logged
Message:
Im not exactly sure what 350.2 means, but I believe its 350 Watts x 2 channels = 700 Watts Peak Power = about 350 Watts RMS. If you have one Kicker L7, and im guessing its probably a 10 inch, then it can take like 650 Watts RMS I think. So look for an amp that matches well with that, and make sure the resistance wont be too low to fry your amp.
|
ANDY
Dodge Dakota
JOIN HERE
4/15/2007
02:10:50
| RE: Kicker L7's
IP: Logged
Message:
ABOUT THE L7 DUDE IT'S ACTUALLY 12 INCH BUT I ALSO HAVE ONE FOSGATE PUNCH P3 ABOUT 1000 WATTS MAX WHAT AMP YOU THINK I SHOULD GET TO MAKE IT BUMP HARD
|
ANDY
Dodge Dakota
JOIN HERE
4/28/2007
17:11:09
| RE: Kicker L7's
IP: Logged
Message:
WHAT KIND OF AMP DO I NEED FOR ONE 12 P3 PUNCH 1000 WATTS MAX 500 RMS
|
| | <<Original Post <<Previous Page P 8 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
