| From | Message |
tex69camaro
Dodge Dakota
JOIN HERE
7/14/2003
02:35:38
|
 Subject: dakota headers -premag
IP: Logged
Message:
hi all-
i have a 88 dakota that is an ex 4 banger. now i got a pre-magnum 318 in there matted up to the 5 sp that was in the car. my question is what headers would work? will a full size truck header work? i dont ahve any laying arround to test fit... :( if those wouldnt work, which im guessing they wont, which ones will work? thanks alot on the advise :)
tex
|
dcxer
Dodge Dakota
JOIN HERE
7/14/2003
03:04:06
| RE: dakota headers -premag
IP: Logged
Message:
If I recall correctly Mopar performance used to stock a header for the pre mag dakota.There might be some around as it was not a very hot item.Might have been for a V-8 Shelby.Check all the header manufacturers.Hope this helps.
|
frank
Dodge Dakota
JOIN HERE
7/14/2003
20:03:25
| RE: dakota headers -premag
IP: Logged
Message:
i have the edlebrock T.E.S header and y pipe set up on my 318. its a very well thought out design and was easy to install. be careful of other shorty headers that dont fit around the brake boost
|
Spencer
Dodge Dakota
JOIN HERE
7/15/2003
02:11:22
| RE: dakota headers -premag
IP: Logged
Message:
mopar doesnt make headers for the v8s in 87-90s, but i know hooker does, and apparently edelbrock does too, now if you needed v6 parts, then i could help you
|
Chris
Dodge Dakota
JOIN HERE
7/15/2003
02:16:45
|  RE: dakota headers -premag
IP: Logged
Message:
Hey spencer, i just got my 99" dak 3.9 about 3 months ago and i want to start doing some mods to my motor. I was woundering what should i do first? Was thinking about muffler and IAF relocation. But dont know what to go to after that. If you got some tips it whould be very helpful.
|
91DakotaFreak
Dodge Dakota
JOIN HERE
7/15/2003
11:01:22
| RE: dakota headers -premag
IP: Logged
Message:
Hooker makes a set of full length headers for 87-91 318 dakotas part number is 5803hkr for black and 5803-1hkr for ceramic coated
|
Jdoggy
Dodge Dakota
JOIN HERE
7/15/2003
15:32:07
| RE: dakota headers -premag
IP: Logged
Message:
I know that the Thorley headers fit the 318 perfectly. Not sure if they will fit with the other mechanics of the truck, you might want to check it out. The only modification i had to make to get these to fit was with the transmission fluid dipstick. I has to order a part which raised and bent the dipstick toward the block. These are the best headers you can get for a stock 318. Quite pricey and hard to find. Took me 4 months to get them. These headers with the powder coating = $700 shipped
|
tex69camaro
Dodge Dakota
JOIN HERE
7/18/2003
16:15:58
| RE: dakota headers -premag
IP: Logged
Message:
thanks guys- those part numbers should help. im hoping to get the dak redone again now. out with the little 318 and the 5 sp. and in with a 415ci small block, prepped 727 and a 9 inch. i guess im tierd of a 13 second truck haha- should be fun :)
thanks again guys
tex
|
janesy
Dodge Dakota
JOIN HERE
7/18/2003
22:20:10
| RE: dakota headers -premag
IP: Logged
Message:
I think the block was the same if so all you need are a set of exhaust manifolds from a 92-93 mag motor the flow similar to the headers but only those years.
BTW you can easily get Thorlies from any dealer, MOPAR headers are made by thorly
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
