| From | Message |
Joel
Unregistered
JOIN HERE
5/18/2001
14:40:21
|
 Subject: mopar pcm help?
IP: Logged
Message:
i just got a mopar pcm from someone but there is no sticker on it with the part number so there any way to tell if it is actually a mopar pcm? i can't put it on yet cause i do not have a 180 t-stat...
|
cbsdakota
Unregistered
JOIN HERE
5/18/2001
16:58:48
| RE: mopar pcm help?
IP: Logged
Message:
Why would you buy something from someone without knowing what it is? Was it a friend? If so, can't you trust him? In case your interested, I have a intake that looks like a stock airbox, but it's really a super-dooper high performance modified airbox that flows over 2000 cfm's! (Wink,wink!) Just picking on you!
|
Joel
Unregistered
JOIN HERE
5/18/2001
17:13:41
| RE: mopar pcm help?
IP: Logged
Message:
i got it off ebay...
|
99DurangoV8
Unregistered
JOIN HERE
5/18/2001
20:22:17
| RE: mopar pcm help?
IP: Logged
Message:
I am selling my PCM on ebay also but the part nubmer sticker is wrinkled from water, maybe it fell off, is there any gummy residue on the top side (as it is mounted)?
|
Joel
Unregistered
JOIN HERE
5/19/2001
00:28:24
| RE: mopar pcm help?
IP: Logged
Message:
yes, i can tell there was a sticker there before...i also noticed that the back of the stock pcm has a hole in it but it seems to serve no purpose and the mopar pcm doesn't have one there at all...
|
Joel
Unregistered
JOIN HERE
5/19/2001
00:32:43
| RE: mopar pcm help?
IP: Logged
Message:
i installed the new pcm and i noticed that when i started my truck the maintenance light comes on and then off again...is this normal, when i put my stock pcm back on it didn't do this...
|
MPJunkie
Unregistered
JOIN HERE
5/19/2001
08:22:35
| RE: mopar pcm help?
IP: Logged
Message:
You got hammered! Throw it in the nearest garbage can or put it for sale on ebay.
|
Blizzard
Gen III
5/19/2001
12:09:27
| RE: mopar pcm help?
IP: Logged
Message:
I'd think you have to reset the 'puter after the swap, did you do that?
Disconnect the battery, turn the ignition on for 15-20 seconds and then connect 'er back up again and try it.
'01 QC 4x4
5.9L, 3.92 LSD, loaded
www.geocities.com/blizzzzard69
|
w henry
Dodge Dakota
JOIN HERE
10/02/2002
12:03:52
| RE: mopar pcm help?
IP: Logged
Message:
Acouple of things you could check will tell you if it is a mp pcm.It should run up to 6000 rpm befor hitting the rev limmiter/cut out.If your engine is built to rev past 5200.ie valve springs.Another thing,put the truck on jackstands,putit in top gear/overdrive and run it. It will have no top end limmit either.Shift points sholld be higher at wof also.The mopar pcm are only reprogramed stock computers anyway.Or call Mike Leach there may be some numbers on it he could check.
|
w henry
Dodge Dakota
JOIN HERE
10/02/2002
12:08:29
| RE: mopar pcm help?
IP: Logged
Message:
Yes,the ececk eng light comes on and goes out every time you start.If it doesnt go out then you have a probiem .You can put it on without the thermostat,wont matter.hope this helps.
|
Troy
Dodge Dakota
JOIN HERE
10/02/2002
12:15:48
| RE: mopar pcm help?
IP: Logged
Message:
If the truck shifts around 4,800 rpm at WOT you have a stock PCM. If it shifts around 5,300 rpm you have the MP PCM. It will also ping real bad on 87 octane if it's the MP unit. There is no need to reset the PCM after installation. Unhook the battery, remove stock PCM, install MP unit, connect battery. My truck starts and stops real fast on the first start-up, then on the second start-up it runs a little rough then smooths out. It will take 100-300 miles for the new PCM to "learn" everything. Hope this helps.
|
DeepDak
Dodge Dakota
JOIN HERE
10/02/2002
14:56:59
| RE: mopar pcm help?
IP: Logged
Message:
You will need to have the dealer flash your vin number and mileage to get rid of the maintence and brake lights. Hope you purchased a pcm without the flash already done.
Eli
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
