| From | Message |
texaslawdawg
Dodge Dakota
JOIN HERE
1/25/2003
22:20:48
|
 Subject: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
I just fininshed installing a set of Harland Sharp aluminum 1.7 roller rockers on my 2002 R/T. Man, these are super easy install. John Mercedes at SoutheastRT helped on the design specifically for our trucks. NO lash or timing to mess with, no guide plates or new rods, just rip out the stock rockers and bolt on the new 1.7's and hit the road. The stock covers even work. It took me and my buddy only 2 hours and we were bullshixxin' most of the time. So if your considering 1.7RR's to use with a stock cam, you cant beat these, only $295 shipped. I just wish I wouldnt have wasted that $550 on the useless B&G flash. Next up 4.56 gears !!
|
slow r/t man
Dodge Dakota
JOIN HERE
1/25/2003
22:38:52
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
I am very interested in these. Do you have a part #????? Where did you get them from???? Any pictures??? Does it run better???
|
dano 360
Dodge Dakota
JOIN HERE
1/25/2003
23:04:21
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
tex, did you notice any gains with the 1.7's ?
|
lello
Dodge Dakota
JOIN HERE
1/25/2003
23:26:00
|  RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Had Harland Sharp 1.6's on my 10 sec late model stang.........nice rockers!! I'll be getting 1.7 for my R/T soon though. Why do you hate the B&G flash?? Had my done for my'02 R/t and like it.
|
texaslawdawg
Dodge Dakota
JOIN HERE
1/26/2003
12:26:51
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Sorry, I threw the box away with the part number, but John Mercedes at SoutheastRT is a distributor and sells them for about $100 under list price, email him at jmmtsb@prodigy.net he is a super good guy and very very busy so be patient, he can answer just about every question that deals with the 5.9 R/T. If you are putting these in a R/T, let me know and I can give you instructions, super easy.
I told my buddy that someone was gonna slam me for not taking pictures, I wish I would have. As far as gains, I just put 'em in last night and didnt want to go wide open immediately but John says about 3/10ths off your quarter mile time and better fuel milage. Ill keep ya'll posted when I really test them out.
lello: The B&G just didnt impress me, maybe cause I got the reg flash for the stock keg intake. I cant tell any difference whatsoever, I think something may be wrong. I called him and he said it was done right. Just chalk that one up as a waste.
|
texaslawdawg
Dodge Dakota
JOIN HERE
1/27/2003
00:27:34
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Should I reset the PCM after my 1.7 RR's are instaled ?
|
rtdkota
R/T
1/27/2003
10:06:51
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Yes, a reset will allow your PCM to set to the factory 'table', and via your O2 & related sensors relearn the new 'parameters' more quickly. Always a good idea after any modification.
Sam
www.socaldakota.com
RTDKOTA
|
Joey
Dodge Dakota
JOIN HERE
5/24/2004
15:58:25
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
recently i installed the 1.7 rockers on my '02 R/T and they definetly made a difference in power. however, 2 wierd things began to happen after they were installed. it seems like i have a ticking sound coming from the engine compartment now and also if i rev up the engine or if im driving along and floor it, it wont always return to the 600rpm idle..... it will often idle at 1500rpm and ill have to rev it again to make it go down. if anyone can tell me wat to do it would be great thanks.
|
rollin
Dodge Dakota
JOIN HERE
5/24/2004
18:01:17
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
You will have some minor valve clatter with roller rockers, as for your idle maybe a vaccum connection.
|
don
Dodge Dakota
JOIN HERE
5/25/2004
02:38:23
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
reset your PCM ? flash? same thing? does a dodge dealer/garage do this? how many $,,, thanks
|
Spali
Dodge Dakota
JOIN HERE
5/25/2004
08:36:01
|  HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
The 1.7's should give you a solid 10HP at the rear wheels and another TRUE .032 of lift to your current cam. This means your engine crank HP may see 15-20HP. It will also make your cam behave like it has another 4 degrees of duration. For $295, it's a very highly recommended and worthwhile mod.
|
another mark
Dodge Dakota
JOIN HERE
5/25/2004
10:47:27
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Don, resetting your PCM can be done by you. Remove negative
battery cable and turn key in ignition to start and hold in place
for about 30 seconds. Then reconnect battery cable. A flash is
where the stock vehicle program in the PCM is replaced with a
more custom tuned one depending on your modifications etc.
The flash will be done by some other company other than the
dealer who only has stock programs. $300-$500 on average for
a flash.
|
eddie
Dodge Dakota
JOIN HERE
4/14/2010
22:36:44
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
where can i get ahold of that john mercedes guy i tried the email address texaslawdawg put up but it doesnt seem to work antone with help it will be greatly appreciated
|
daddio
Dodge Dakota
JOIN HERE
4/15/2010
09:18:20
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
eddie, the original post is over 7 years old. why don't you just search the webz for Harlan Sharp Roller Rockers. I bet you'll get a ton of hits on it.
|
eddie
Dodge Dakota
JOIN HERE
4/16/2010
10:53:32
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
I did that but they are like 600 dollars on the web this guy says he can get for 295 direct from johb mercedes
|
daddio
Dodge Dakota
JOIN HERE
4/16/2010
10:59:06
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
I guess you didn't get the fact that the post is over 7 years old! I'm sure with inflation they would have gone up in price. Check summitracing.com.
|
daddio
Dodge Dakota
JOIN HERE
4/16/2010
11:53:17
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Or you could try here:
http://southeastrt.com/
|
eddie
Dodge Dakota
JOIN HERE
4/18/2010
00:28:56
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
thanks alot man i just found them
|
eddie
Dodge Dakota
JOIN HERE
4/18/2010
00:31:21
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
are these hard to put on do you know your self by any chance
|
daddio
Dodge Dakota
JOIN HERE
4/18/2010
08:49:54
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
Eddie, go and check you post here:
https://www.dodgedakota.net/boards/gen/27728.html
And stop jumping around for answers to the same questions. You'll have info spread out all over this board and neverget your answers.
|
T.C.
Dodge Dakota
JOIN HERE
6/22/2010
10:04:14
| RE: HArland Sharp 1.7 Roller Rockers
IP: Logged
Message:
no they are not hard to install, remove valve covers and old rocker arms, then wrench the new ones on at about 23-24 lbs./tq. it took me about an hour, its simple
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
