| From | Message |
TJ
Dodge Dakota
JOIN HERE
8/25/2002
19:17:39
|
 Subject: M1 intake
IP: Logged
Message:
Does anyone know if the M1 will void my warranty?
If so, is the performance gain worth the risk of voiding the warranty? I have an 2002 R/T cc with intake, exhaust, and a jet chip(waste of money).
Any help would be appeciated. Thanks guys.
|
kota on 20s
GenIII
 
8/26/2002
00:45:00
|  RE: M1 intake
IP: Logged
Message:
you warrenty will be good with the manifold
-Eric
Injection is nice, but i'd rather be blown.
5.2L, 5speed. Powerdyne SC, 50mm TB, 2bbl M-1, 1.7RR's, MSD 6BTM, ciramic JBA headers, carsound cat, dumped gibson
|
TJ
Dodge Dakota
JOIN HERE
8/27/2002
09:23:25
| RE: M1 intake
IP: Logged
Message:
Thanks for the reply. Do you also know if my truck will run right with the stock pcm and M1? Mopar doesnt make the controller for my truck.(only up to 2000)
|
parts manager
Dodge Dakota
JOIN HERE
8/27/2002
09:58:13
| RE: M1 intake
IP: Logged
Message:
my 99 R/T feels like it's a v-10 with that intake but i do have the mopar performance controller to me its the best accessory i installed on my R/T
|
TJ
Dodge Dakota
JOIN HERE
8/27/2002
13:02:45
| RE: M1 intake
IP: Logged
Message:
Did you have the controller before the M1? If so did it make a big difference then, without the M1?
|
TJ
Dodge Dakota
JOIN HERE
8/27/2002
13:05:24
| RE: M1 intake
IP: Logged
Message:
Also did you lose alot of torque?
|
DaveR
Dodge Dakota
JOIN HERE
8/27/2002
13:20:42
| RE: M1 intake
IP: Logged
Message:
I had the PCM before the M1 on my 94'. The was a bit of a difference when I changed to the proformance controler, but nothing like the change after I put on the intake. I don't feel I lost torque, I almost think I make a little more.
|
TJ
Dodge Dakota
JOIN HERE
8/27/2002
14:42:13
| RE: M1 intake
IP: Logged
Message:
Hey Dave what other mods do you have if you dont mind me asking? Have you taken it to the track at all?
|
DaveR
Dodge Dakota
JOIN HERE
8/27/2002
14:57:14
| RE: M1 intake
IP: Logged
Message:
It's just and little 5.2. But, headers, custom machined TB, MSD 6AL, Blaster 2 coil, flowmaster catback, Ram air induction. I think there is something else, but i can't seem to remember. I had it dynoed recently and I turned 210.9hp @ 255ft/lbs. If you want to know what I made in specific RPM ranges I can tell you.
|
TJ
Dodge Dakota
JOIN HERE
8/27/2002
15:02:41
| RE: M1 intake
IP: Logged
Message:
Was your M1 hard to install?
|
DaveR
Dodge Dakota
JOIN HERE
8/27/2002
15:35:18
| RE: M1 intake
IP: Logged
Message:
I have installed harder things and I made it even harder for myself by not getting the intall kit with it. It's not that bad though and the instructions are decent. I wish there were more pictures in the instructions, but it wasn't that bad. I can't say i'd recomend doing it unless you have a decent mechanical knowledge and a working knowledge of what's what under the hood. I thought it was pretty strait forward though.
|
| | P 1 |
|
Post a reply to this message:
Username Registration: Optional
All visitors are allowed to post messages
|
